Hjemmeside 2 pvp
Coach Outlet Coach Factory Outlet Coach Outlet Store Coach Handbags Outlet Coach Outlet Coach Factory Outlet Coach Outlet Coach Handbags Coach Site Michael Kors Outlet Michael Kors Handbags Outlet Cheap Michael Kors Michael Kors Outlet Michael Kors Handbags Outlet Cheap Michael Kors Michael Kors Outlet Michael Kors Handbags Outlet Cheap Michael Kors Cheap NFL Jerseys China Cheap NFL Jerseys Free Shipping Wholesale NHL Jerseys China Wholesale Jerseys From China Cheap NFL Jerseys Free Shipping Cheap NFL Jerseys For Sale Cheap Jerseys Free Shipping Wholesale NFL Jerseys From China Cheap NFL Jerseys Sale Cheap Nike NFL Jerseys China Wholesale Jerseys Free Shipping Cheap NFL Jerseys Wholesale Wholesale NFL Jerseys Online Cheap NFL Jerseys Wholesale Cheap Jerseys Free Shipping Cheap NFL Jerseys China

New PVP chassis model 2010

Below on this page can you see photo and all the details

The new chassis have bracket for the new side bare (side bumper)

On the new 2010 PVP chassis can you adjust the height over the ground on the front and the rear end of the kart, the highest positions is the same as chassis from 1996 to 2008, and you can now adjust it 12 mm. down in 3 mm. steps, the connection between the caliper and the house to rear axle bearing, make sure you always have the correct distance between the caliper and the brake disk, then you change the riding height.

You can not use this system on the old type of PVP kart, there is not spaces under the chain adjuster and the bracket on the old kart is 6 mm. lover than on the new model 2010.    

 

 

There is a new bracket to the wing left hand side is part number 1291

There is also a new bracket to the wing right hand side is part number 1292

A new bracket for the diagonal tube to the wing, part number 1293, the diagonal tube is 10x385 mm, part number 1569  

 

On the new chassis is it also necessary to have new rear seat mount, this is 20 mm. lover than before and give more spaces to the seat, part number 1322

Here can you see the step for height adjustment, the house for the rear axle bearing fit to both 3055 and 3057, the part number for the alum. house is 3058  

Part number for this bracket is 1595

You have to make new hole in the inside plate for the wing, 

If the kart is from 1996 to 2005 then do you have to drill the hole 50 mm. longer back and 10 mm. lower.

If the kart is from 2006 to 2008 then do you have to drill the hole 30 mm. longer back and 10 mm. lower.

On PVP chassis model 2010 can you also adjust front end height over the ground with 12 mm. on the photo below can you see the highest riding positions, and if you move washer from the top to the bottom (eats washer is 1.5 mm. so there is 8 washer) will you lover the front end of the chassis without change the camber and caster angel, but you have to adjust the tow in, You will get a almost correct adjustment if you turn one of the rod end R/H type, one round in for eats 3 mm. you lover the front end of the kart.  

Importen: always have the front end minimum 4 mm. lower than the rear,( if you measure under the floor tray),  if the front end is to high, will you lose the ground effect, and lose the grip in the track.

O the photo below can you see the loves position, I will recommend if you drive on Dunlop tires to lover front and rear the same, Bridgestone front tires is smaller in diameter and you need to adjust the front so it will fit to this.

Chassis 1004 is made for Single cylinder motor and Yamaha TZ

cheap nfl jerseys china cheap nfl jerseys free shipping wholesale nfl jerseys china wholesale jerseys from china cheap